AK440 Posted December 31, 2023 Share Posted December 31, 2023 I just picked up a beautiful ‘07 F8 Sno-Pro and want to adjust the oil pump. What’s the easiest way to remove the belly pan to get at it? Drill all the rivets out or use a grinder? Quote Link to comment Share on other sites More sharing options...
Deephaven Posted December 31, 2023 Share Posted December 31, 2023 Should just put it in a museum and buyz a real sled instead. 1 Quote Link to comment Share on other sites More sharing options...
AK440 Posted December 31, 2023 Author Share Posted December 31, 2023 There’s nothing wrong with picking up an older sled now and again just for fun. It’s obvious you’re too stupid to help so instead of remaining silent you opened your mouth and removed all doubt. 1 Quote Link to comment Share on other sites More sharing options...
Not greg b Posted December 31, 2023 Share Posted December 31, 2023 Use a crows foot like normal people. Dial it back until it blows up. Rebuild and add a turn and 1/2 and it is good 2 Quote Link to comment Share on other sites More sharing options...
AK440 Posted December 31, 2023 Author Share Posted December 31, 2023 4 minutes ago, Not greg b said: Use a crows foot like normal people. Dial it back until it blows up. Rebuild and add a turn and 1/2 and it is good So you’re a dipshit too, got it. Quote Link to comment Share on other sites More sharing options...
mnstang Posted December 31, 2023 Share Posted December 31, 2023 I would question removing the skid plate. Not sure on that particular model but sometimes there is a barrel adjuster at the midway point of the cable and you can adjust it there. When in doubt, look at the service manual. It's usually better information than a random yahoo on the internet. I've been down the road of adjusting oil pumps, got bit once doing that. It's best to leave them but if you do, adjust to factory marks, don't try to calculate consumption and adjust based on that. I've found they're usually at 30-35:1 factory but if you lean it to try for 50:1, that's 50:1 overall but there might be an RPM or throttle setting where it's getting much less than that and that can be trouble. 1 Quote Link to comment Share on other sites More sharing options...
krom Posted December 31, 2023 Share Posted December 31, 2023 (edited) Not sure why I'm helping.. but you go at it from the exhaust side with a mirror to check. taking off the bottom pan won't do you any good there is no cable to adjust, its a rod between the pump and throttle bodies A better question is why do you want to adjust it in the first place, because if you don't know how to do it, you are better off leaving it alone. Oil is way cheaper than parts are Edited December 31, 2023 by krom 4 Quote Link to comment Share on other sites More sharing options...
Gold Member EvilBird Posted December 31, 2023 Gold Member Share Posted December 31, 2023 Quote Link to comment Share on other sites More sharing options...
AK440 Posted December 31, 2023 Author Share Posted December 31, 2023 3 hours ago, mnstang said: I would question removing the skid plate. Not sure on that particular model but sometimes there is a barrel adjuster at the midway point of the cable and you can adjust it there. When in doubt, look at the service manual. It's usually better information than a random yahoo on the internet. I've been down the road of adjusting oil pumps, got bit once doing that. It's best to leave them but if you do, adjust to factory marks, don't try to calculate consumption and adjust based on that. I've found they're usually at 30-35:1 factory but if you lean it to try for 50:1, that's 50:1 overall but there might be an RPM or throttle setting where it's getting much less than that and that can be trouble. 3 hours ago, krom said: Not sure why I'm helping.. but you go at it from the exhaust side with a mirror to check. taking off the bottom pan won't do you any good there is no cable to adjust, its a rod between the pump and throttle bodies A better question is why do you want to adjust it in the first place, because if you don't know how to do it, you are better off leaving it alone. Oil is way cheaper than parts are When you pop the arm off the oil pump, won't it "spring away" on you? I agree it looks easier to adjust from the top (with the throttle wide open), but I am nervous the oil pump arm will drop down (my term of "spring away") towards the bottom of the engine ... and then that leaves a guy stuck trying to find a way to hook the arm back into the pump itself. Quote Link to comment Share on other sites More sharing options...
AK440 Posted December 31, 2023 Author Share Posted December 31, 2023 1 hour ago, EvilBird said: Shitbird can’t even come up with a good line. Too stupid to help, too stupid to write words. Quote Link to comment Share on other sites More sharing options...
Gold Member EvilBird Posted December 31, 2023 Gold Member Share Posted December 31, 2023 (edited) 7 minutes ago, AK440 said: Shitbird can’t even come up with a good line. Too stupid to help, too stupid to write words. Bro you wanted to take the belly pan off to do a oil pump adjustment. And you asked how to remove rivets. A 12 year old could figure that out in his Shed . And You call others a bad mechanic. So rich. Edited December 31, 2023 by EvilBird Quote Link to comment Share on other sites More sharing options...
AK440 Posted December 31, 2023 Author Share Posted December 31, 2023 13 minutes ago, EvilBird said: Bro you wanted to take the belly pan off to do a oil pump adjustment. And you asked how to remove rivets. A 12 year old could figure that out in his Shed . And You call others a bad mechanic. So rich. I had it on good authority that removing the belly pan was the best way to get at the oil pump. Quote Link to comment Share on other sites More sharing options...
Gold Member EvilBird Posted December 31, 2023 Gold Member Share Posted December 31, 2023 1 minute ago, AK440 said: I had it on good authority that removing the belly pan was the best way to get at the oil pump. fair enough. just the way you talk i figured you were some master tech Quote Link to comment Share on other sites More sharing options...
AK440 Posted December 31, 2023 Author Share Posted December 31, 2023 8 minutes ago, EvilBird said: fair enough. just the way you talk i figured you were some master tech I am some master tech. When I read that a guy has to remove a belly pan to get at an oil pump that struck me as odd so I asked the question. Quote Link to comment Share on other sites More sharing options...
Laborer Posted December 31, 2023 Share Posted December 31, 2023 I dialed it back on my 07. I remember going in from the top. I believe I used a long regular screwdriver and long needle nose pliers. Like every one else said, probly just leave it alone? Quote Link to comment Share on other sites More sharing options...
krom Posted December 31, 2023 Share Posted December 31, 2023 24 minutes ago, AK440 said: I am some master tech. When I read that a guy has to remove a belly pan to get at an oil pump that struck me as odd so I asked the question. No one who has ever worked on a twin spar sled would say to remove the bottom pan... And yes the lever will drop down when you unhook the rod. But again why are you adjusting it in the first place. Quote Link to comment Share on other sites More sharing options...
Bontz Posted December 31, 2023 Share Posted December 31, 2023 6 minutes ago, krom said: But again why are you adjusting it in the first place. Exactly my first thought - why would this be something considered when the sled is new to someone? It would take a few rides and some miles to see how much oil it's even using before ever considering an oil pump adjustment. You're also way too nice Krom ... I'd tell this cocksucker to use the old Google machine since he's such an expert at everything (well, other than adjusting an oil pump on an old sled) 1 3 Quote Link to comment Share on other sites More sharing options...
Crnr2Crnr Posted December 31, 2023 Share Posted December 31, 2023 you'll find the information somewhere between page 1 and page 649 https://support.countrycat.com/posts/2805804-2007-2-stroke-service-manual or, just listen to Krom who's been around these things since Moses was a kid Quote Link to comment Share on other sites More sharing options...
AK440 Posted December 31, 2023 Author Share Posted December 31, 2023 47 minutes ago, krom said: No one who has ever worked on a twin spar sled would say to remove the bottom pan... And yes the lever will drop down when you unhook the rod. But again why are you adjusting it in the first place. Don’t be too sure about that. It’s pretty common from what I understand. Based on the amount of oil/exhaust residue on my side panel, and the black plugs I've got going ... it's going to need a couple turns. I really hope it's something that simple that wakes this sled up, but my guess is that I'm gonna be dicking around with a lot of clutching too. Oh well, that's part of the fun :wink 38 minutes ago, Bontz said: Exactly my first thought - why would this be something considered when the sled is new to someone? It would take a few rides and some miles to see how much oil it's even using before ever considering an oil pump adjustment. You're also way too nice Krom ... I'd tell this cocksucker to use the old Google machine since he's such an expert at everything (well, other than adjusting an oil pump on an old sled) Huh… interesting.🧐 Quote Link to comment Share on other sites More sharing options...
krom Posted December 31, 2023 Share Posted December 31, 2023 2 minutes ago, AK440 said: Don’t be too sure about that. It’s pretty common from what I understand. Then you should pull the pan, and try it that way, lmk how it goes 1 2 Quote Link to comment Share on other sites More sharing options...
AK440 Posted December 31, 2023 Author Share Posted December 31, 2023 1 minute ago, krom said: Then you should pull the pan, and try it that way, lmk how it goes I’d feel like a retard if I did it that way, it’s sounding like their is an easier method. Quote Link to comment Share on other sites More sharing options...
krom Posted December 31, 2023 Share Posted December 31, 2023 (edited) We only sold a thousand or so of them over the years, but what the fuck do I know Edited December 31, 2023 by krom 1 Quote Link to comment Share on other sites More sharing options...
AK440 Posted December 31, 2023 Author Share Posted December 31, 2023 2 minutes ago, krom said: We only sold a thousand or so of them over the years, but what the fuck do I know So your saying to pull the belly pan now? I’m confused? Quote Link to comment Share on other sites More sharing options...
Bontz Posted December 31, 2023 Share Posted December 31, 2023 11 minutes ago, AK440 said: I really hope it's something that simple that wakes this sled up, but my guess is that I'm gonna be dicking around with a lot of clutching too. Oh well, that's part of the fun :wink Huh… interesting.🧐 Why do you think Cat came out with the H.O. a couple seasons later and ultimately went away from the 1000, too? That was a bad "performance" sled in the 07-08 models, that was way overhyped coming off the Firecat success. Oh, and have fun getting it unstuck if you're off trail Quote Link to comment Share on other sites More sharing options...
Crnr2Crnr Posted December 31, 2023 Share Posted December 31, 2023 35 minutes ago, AK440 said: Don’t be too sure about that. It’s pretty common from what I understand. Based on the amount of oil/exhaust residue on my side panel, and the black plugs I've got going ... it's going to need a couple turns. I really hope it's something that simple that wakes this sled up, but my guess is that I'm gonna be dicking around with a lot of clutching too. Oh well, that's part of the fun :wink Huh… interesting.🧐 I'd check compression, degrease everything and start hunting for leaks before fucking with the oil pump... oh, the irony of that statement coming from me right now Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.