SHADOSPRIT Posted October 30, 2022 Share Posted October 30, 2022 OK I know this isn't current events, but not sure where to put this! I have a Craftsman 33 gallon air compressor. Today I needed to use my cut off tool which I have never had a problem with. Built pressure and as soon as I put the cut off tool on the screw, it would barely move! OK did a bit of troubleshooting, cut off tool went bad....Down to the store I go new one in hand. Back to garage same problem. OK compressor not putting out what gauges says. Ended up replacing output valve. Cut off tool back on, same issue. I can put my finger on it and it slows down? Any Ideas? I have no way of measuring outcoming air pressure. but to me, It doesn't seem right. I can put my finger over the air chuck and stop the air? Don't think this is right? Any input? even if gauge was bad, still shouldn't be able to stop it completely with my finger????????????? Quote Link to comment Share on other sites More sharing options...
SkisNH Posted October 30, 2022 Share Posted October 30, 2022 Pumps bad?, are you sure it's building pressure. Quote Link to comment Share on other sites More sharing options...
SHADOSPRIT Posted October 30, 2022 Author Share Posted October 30, 2022 There are to guages one tells me what's in tank, its,reading 140-150 psi....second guage is outgoing...shows 100-120 going out. Quote Link to comment Share on other sites More sharing options...
spin_dry Posted October 30, 2022 Share Posted October 30, 2022 Is there a drier/filter in the line between the tank and tool? If so, check if it’s plugged. Could be a failed pressure regulator as well. Quote Link to comment Share on other sites More sharing options...
SHADOSPRIT Posted October 30, 2022 Author Share Posted October 30, 2022 Nothing in line, brand new pressure regulator. Gonna try and rig something up tomorrow. Just doesn't seem like the outcoming pressure is right. Maybe bad regulator? I would think 1 of the guages would be kinda right... Quote Link to comment Share on other sites More sharing options...
Mainecat Posted October 30, 2022 Share Posted October 30, 2022 Release the relief valve and empty all the tank air. Quote Link to comment Share on other sites More sharing options...
SHADOSPRIT Posted October 30, 2022 Author Share Posted October 30, 2022 I empty tank every night i do it out the bottom. There is a ball valve, seem to get great pressure out of that. Can't block that with my finger like I can tje output... Quote Link to comment Share on other sites More sharing options...
Guest Posted October 30, 2022 Share Posted October 30, 2022 If you can hold your finger over the chuck and stop the air your line pressure gauge isn't reading correctly. Sounds odd but the regulator isn't allowing full line pressure.Can you manually try increasing the line pressure to max or is it there already? Do you blow the tank down for moisture regularly? Quote Link to comment Share on other sites More sharing options...
SHADOSPRIT Posted October 30, 2022 Author Share Posted October 30, 2022 Line pressure is at max....I blow it out every night. Wonder if something passed thru and is lodged in there, or maybe got a bad output regulator Quote Link to comment Share on other sites More sharing options...
motonoggin Posted October 31, 2022 Share Posted October 31, 2022 Yeah sometimes those regulators have a porous screen in them and that'll clog with shit and it'll make your pressure look right but flow will suck. We used to remove them before we installed new ones for gas lift systems and such. A flat head screwdriver and a hammer will knock it loose. Quote Link to comment Share on other sites More sharing options...
awful knawful Posted October 31, 2022 Share Posted October 31, 2022 10 hours ago, SHADOSPRIT said: OK I know this isn't current events, but not sure where to put this! I have a Craftsman 33 gallon air compressor. Today I needed to use my cut off tool which I have never had a problem with. Built pressure and as soon as I put the cut off tool on the screw, it would barely move! OK did a bit of troubleshooting, cut off tool went bad....Down to the store I go new one in hand. Back to garage same problem. OK compressor not putting out what gauges says. Ended up replacing output valve. Cut off tool back on, same issue. I can put my finger on it and it slows down? Any Ideas? I have no way of measuring outcoming air pressure. but to me, It doesn't seem right. I can put my finger over the air chuck and stop the air? Don't think this is right? Any input? even if gauge was bad, still shouldn't be able to stop it completely with my finger????????????? Air hose delaminating on the inside? 1 Quote Link to comment Share on other sites More sharing options...
SHADOSPRIT Posted October 31, 2022 Author Share Posted October 31, 2022 (edited) Nope I can put my finger on the output of the compressor, no hose attached, and can stop 120 lbs of air with my finger, very easily... Edited October 31, 2022 by SHADOSPRIT Quote Link to comment Share on other sites More sharing options...
XCR1250 Posted October 31, 2022 Share Posted October 31, 2022 Remove the line from the compressor to the tank/regulator, see if you can still hold it back with your finger. Directly from the compressor. Quote Link to comment Share on other sites More sharing options...
SHADOSPRIT Posted October 31, 2022 Author Share Posted October 31, 2022 3 hours ago, XCR1250 said: Remove the line from the compressor to the tank/regulator, see if you can still hold it back with your finger. Directly from the compressor. Yes I can, little more difficult than at the end of the hose but I can at the compressor. Stopped bought a new regulator today. Swapped it out but still doesn't seem to have the output it should. When I swapped out the regulator, I turned on the compressor and it seems to be producing the proper pressure. As soon as I put on the regulator, it seems to drop drastically. 2-3 bad regulators? all from different stores? Quote Link to comment Share on other sites More sharing options...
Platinum Contributing Member steve from amherst Posted October 31, 2022 Platinum Contributing Member Share Posted October 31, 2022 20 hours ago, SHADOSPRIT said: I empty tank every night i do it out the bottom. There is a ball valve, seem to get great pressure out of that. Can't block that with my finger like I can tje output... Change the output fitting Quote Link to comment Share on other sites More sharing options...
SHADOSPRIT Posted October 31, 2022 Author Share Posted October 31, 2022 49 minutes ago, steve from amherst said: Change the output fitting Hmmm never thought about that.... Quote Link to comment Share on other sites More sharing options...
polaris7541 Posted October 31, 2022 Share Posted October 31, 2022 hose collapsed or the out put fitting Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.