Everything posted by thewayout
-
350 Mag MPI
Well, you don’t just lose 10 mph and a bunch of performance if everything is the same and new, unless something is seriously wrong with the reman and it has low compression already.
-
350 Mag MPI
Assuming everything expect the motor is the same, I wonder if you didn’t get the mag version of the 350.
-
350 Mag MPI
No different then taking a pickup for instance and putting grocery gears in it vs say 4.10s. Gear ratios make a world of difference and if you prop for one and it happens to be different then what you actually have, it’s no different then putting 35s on a jeep with stock fuel economy gearing. Performance sucks and it will eat gas
-
350 Mag MPI
Something sound off. If the engine is running strong and is considered to be in good running condition and not making less then advertised power, I’d suspect something else is going on. If they replaced the gearcase with say an alpha or a bravo, and it was different then the original lower, the gear ratios could be different and you would definitely have to reprop.
-
350 Mag MPI
Shit it takes, what 5 minutes to swap a prop out? 1 cotter pin, slide it off, put the new one on, and go. If you are looking for general performance then you will sacrifice one metric for the other. It sounds like you want hole shot and midrange pulling power, so I would be looking to prop down a bit. Stainless has its advantages with a boat that big and heavy with that much torque.
-
350 Mag MPI
Same original outdrive with the same gear ratio lower unit? Both the original and reman are Mag versions?
-
350 Mag MPI
Another option is to have multiple props for various uses. One can be for water sports and pulling power that will give you a good hole shot and midrange power, but slower top speed. This will be a lower pitch prop. The other can be a more performance oriented blade if that’s what you want, that sacrifices hole shot for speed. You can’t have both, there’s always a sacrifice in propping, one way or another. You have to be mindful of selection, dropping 1 pitch increases max rpm 200 or so is the general rule of thumb. One last question, are you running stainless or aluminum?
-
350 Mag MPI
What’s the max rpm you are running on a light load? Is it in the upper range of max rpm for that 350? If I had to guess that engine is low 5s for max upper rpm range (4800-5200?) always shoot for upper rpm with a light load which will bring you to the low end of the max rpm range with some weight in or behind the boat otherwise you will be lugging and losing performance. It sounds like it’s overpropped to me. What prop are you running currently? Diameter and pitch. does the prop have exhaust venting holes on drilled in the outside diameter of the prop just above the labyrinth seal diameter?
-
Official 2020/2021 Snowmobile Season
I’m getting 0, you’re welcome! Nice trailer btw!!
-
Rumour is an 850 matryx can’t even beet a 2019 cat 800 RR
Well, not mine or Preston’s. Maybe some are but all cats are for sure bro.
-
Rumour is an 850 matryx can’t even beet a 2019 cat 800 RR
@ACE @bussman 800 and his buddies 2020 8000 both saw my 850 doo snow flap across the lake, couldn’t see how many sled lengths behind they were. Also, the 850 etec midrange is significantly better then the cat, it’s not even close. Bottom end Brian’s cat pulls as hard as my xcr did almost, it’s very strong down low. I liked his sled a lot he has it set up great, it just doesn’t fit me well personally. the etec 850 is superior. That’s just the truth.
-
Shaper Bars
7.5 shapers here with stock 4” outsides on shimmed pilot 5.7s. 129” xrs. The sled rips and handles well. I’ve used shapers on everything I’ve owned and swear by them. They’ve worn great for me, but you have to shim your skis.
-
Official how many sleds have you wrecked ?thread
XLT story is one of my favorites.
-
Jesus sled confirmed. Cat will never be as good
Red and grey is just not right
-
Official 2020/2021 Snowmobile Season
I like my modular 3 a lot fwiw. Obviously heavier and not a moto style but it’s been used a lot and held up very well.
-
Gapes and Wails
Preston got the X because of that, he wanted more top end. Even changed shocks out for it and did some work. My bone stock sled was side by side with him on the lake lol.
-
Gapes and Wails
The 6.2 is very regarded unlike the cat 800. Might as well have a 5.3 or 4.8 under the hood.
-
Gapes and Wails
I raced 2 800 cats last year for over a mile wide open on a lake and both my 18 xrs and Preston’s 19 X 850 laid the gape to busscarps 19 and his buddies 20. The xrs and X were literally identical, the cats were at least a few sleds behind if not more, I couldn’t tell with all the snow dust behind me. #gape
-
What sleds do you own and actively ride?
Loved that sled. Best one to date that I’ve owned.
-
What sleds do you own and actively ride?
Power compared to the 800?
-
What sleds do you own and actively ride?
Makes sense. Glad she enjoys riding! My wife is a mixed bag, she likes the short trips in the evenings when we have good snow down south. She doesn’t like the extended weekend trips with big mileage days.
-
What sleds do you own and actively ride?
Dude that assault is beautiful. The axys chassis is so badass. You’re going to love it. Congrats. I miss my xcr.
-
What sleds do you own and actively ride?
Nice lineup. Your wife prefers the vector to the XS doo? 600 or 800 etec?
-
What sleds do you own and actively ride?
How do you like the matryx compared to the axys?
-
What sleds do you own and actively ride?
That HO Suzuki was the last good cat 800