polaris7541

need to replace the prop , hit a rock ,, just looking for improvements out of the hole and on top speed

prop is aluminum.

yep prop that came on it is a 14.5x 19 pitch 3 blade , its a 4 wynns cuddy cabin ,, 5.0 stern drive ,, 4 wynns states prop should be a 14 1/4 x 19 pitch . highest rpms i can get is 3800 on a good day at 35 mph on gps, 4 wynns states max rpms should be 4000 / 4500,, motor and drive have been replaced prior me buying the boat , only has 75 hours on motor , problem is there are are 2 5.0 listed for this boat mine is to be the 200 pony one , the other is 185 , not sure which one i have ,,

ok if i go to a 17 pitch will that have more top end speed , from the math sounds like the rpm s will go up , i think i need to find out what the drive ratio is also , boats pretty clean ,, motors been replaced ,, it might not be marine drives been replaced as well , dose seem like all the work was done proper, , but who knows,, theres to versions of the motor ,ones 185 ponies , the other 200, that could be issue as well, thanks for the inputs

boats is to hit 4000 too 4500 rpms , most i can get is 3800 with the 14 ,5 x 19 pitch checked with 4 wynns they say it should be a 14 1/4 x 19 pitch the 14.5 is what came on the boat the spare prop i have is a 14 1/4 x 21 pitch , so im thinking i should get a 14 1/4 x 19 then

bought this boat used , pretty sure its a frankenstein ,92 4 wwynns 205 prop that was on it is a 14.5 x19 pitch,, original prop is to be a 14/ 1/4 x 19 pitch , at 3500 rpms . almost wfo . i can get 35 gps mph,, should i go with a 14/14 x19 or 14 /1/4 x 21 any help would be great ,, it does take a long time to plane out ,, motor is a target 5.0 has 80 hours on it seems to run ok

you just drill 2 new holes and use some 90 degree picks, drill about 1/4 back on each break . take a punch beat the chit out of the ring to loosen it up , put your pics in , should come write out

yep todays wrenches are very problematic there's only a few good ones left ,, they will run a flow chart ,or goggle shit till you are broke

pulling the boat out , and get it ready IMG_2298.MOV

tanks , I knew it was a good idea

only thing that will save bud , is to publicly castrate that tran over a bud light , enough said

would think it would be a little more than carbides,, hy fax will get damaged sand and grit into places it shouldn't be, hard launches [low snow cond ] belt over heat , hot spots on clutch faces,, ect ect

understand the need , I would never ride my sled in conditions like that ,, sorry I respect machines

now thats a pic polaris powa

think she needs a BIG DICK stuck in her mouth

hard to believe granhole wants the military to go EV , now I have heard everything,, hold on commie guy while i plug my tank in ,, gotta be kidding , enough is enough.

i have a 2x4 just need to know were to put it

Mediterranean chicken salad,,,, zoop

NNNNNNNNNNNNNNNNNNNNNNNNNNNNOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOO

decided to pull the motor apart, on the way I found a brokein carb slide jammed in the reed cage,, decided to re ring it , replaced slides with the black ones , fired up yesterday , all is good ,, thanks for the input

re ringed motor , new slides installed ,, fired it up yesterday , everything all good again

lucky mine got trapped in the reed cage , ended up getting new at 115.00 a crack,, ouch hope it fixes all my issues

riddle me this , SO WHATS WRONG WITH THE ONES THAT WANT TO VOTE for pedo joe , must be s8cking all there dicks then

venison fajitas fried rice and beans